Lining paper thickness

If you are planning on decorating a room and the walls aren’t that good your best option would be to line the walls with lining paper first.

So what thickness should you use?

Lining paper comes in different thickness known as ‘grades’.
The grades range from 800 to 2000 and vary quite a lot in thickness between the lowest to the highest grade.

Some ‘DIY’ stores only stock the lower grades of lining paper, maybe up to 1200 if you’re lucky, but normally only up to 1000 grade. You can buy the thicker grade papers form ‘trade’ outlets, local suppliers or online.
Continue reading Lining paper – What thickness should I use?

Painting a flush door

This tip applies to both interior and exterior flush doors. Flush doors have no panels on them so you may find it easier and quicker to use a gloss roller to paint the door, see the note at the end of this tip.

The first job is to remove the door furniture such as handles, letterbox, knocker etc, now cover the floor. The next job is to remove any loose paint as well as any dirt and grime. Next rub the door down, depending on the surface you are painting over and its condition 80-grit sandpaper will be fine. Rub down, going in the direction of the grain.

Once you have ‘keyed’ the surface with the sand / glass paper dust off the surface. If the door has any bare wood showing you will need to use the appropriate primer. Once the primer is dry you can paint the door with a suitable undercoat, finally the finish coat (woodstain, gloss or satinwood etc) of your choice.

So what order do I paint the flush door?

OK, here is the order to paint your flush door:

If you imagine the door split up into sections, say 6 sections. (Shown as red line in diagram). You may want to work in smaller sections, so divide the door into 8 sections. You should work quickly and complete the door in one go.

1. Paint the door edge, you should always paint the edge you will see if the door is open. Number 1 in diagram. If it is an exterior door you should also paint the top of the door, and the bottom if you can.
2. Paint the first two sections. Numbers 2 and 3 in the diagram.
3. Paint the next two sections. Numbers 4 and 5 in the diagram. Blend the paint of section 2 and 4 with long brush strokes, do the same for section 3 and 5.
4. Finally paint the two remaining sections. Numbers 6 and 7 in diagram. Blend the sections as before.
5. If you are using gloss, check to ensure the paint hasn’t run, if there are runs simply brush them out.
6. You should now have a newly painted door!

NOTES:
If you are using a gloss roller, work in the same way as above and when the entire door is covered, roll from top to bottom across the door, then do it again but this time without applying any preasure to the roller, this should eliminate any ‘air’ bubbles the roller may have left.

This tip applies to both interior and exterior panelled doors, it doesn’t matter how many panels there are, whether it be a 1, 2, 4 or 6 panelled door, the principle is the same.

The first job is to remove the door furniture such as handles, letterbox, knocker etc, now cover the floor. The next job is to remove any loose paint as well as any dirt and grime. Next rub the door down, depending on the surface you are painting over and its condition 80-grit sandpaper will be fine. Rub down, going in the direction of the grain, if you have an internal ‘grain effect’ door be careful not to rub too hard!

Once you have ‘keyed’ the surface with the sand / glass paper dust off the surface. If the door has any bare wood showing you will need to use the appropriate primer. Once the primer is dry you can paint the door with a suitable undercoat, finally the finish coat (gloss or satinwood etc) of your choice.

So what order do I paint the panel door?

OK, here is the order to paint your panel door:

1. Paint the door edge, you should always paint the edge you will see if the door is open. Number 1 in diagram. If it is an exterior door you should also paint the top of the door, and the bottom if you can.
2. Paint the panels. Numbers 2-7 in diagram.
3. Paint the top mullion and rail, numbers 8 and 9 in diagram, and work through all mullions and rails finishing with the bottom rail. Number 14 in diagram.
4. Finally paint the two stiles. Numbers 15 and 16 in diagram.
5. If you are using gloss, check to ensure the paint hasn’t run off the panels, if there are runs simply brush them out with a dry brush.
6. You should now have a newly painted door!

NOTES:

Stiles: vertical parts
Mullion: vertical parts between panels
Rails: horizontal parts
Panels: moulded ‘inset’ shaped areas